Home > Hard Drive > Western Digital Sata Hard Drive Jumper Settings

Western Digital Sata Hard Drive Jumper Settings

Contents

Keep this in mind though, a HDD won't show up in "My Computer", (or "Computer"), until it has been formatted. Dec 5, 2010 #2 alguy TS Rookie Topic Starter thanks for the reply @mailpup, I cannot change anything in the SATA controller mode because I don't see it under the BIOS October 31, 2011 Dave Are there any jumpers on the drive? I try enter in bios but i don't see any sata configuration only ide configuration and that are on auto. http://divxeo.com/hard-drive/ide-hard-drive-jumper-settings.html

If you open the case, you should see a battery that resembles a watch battery-but is about the size of a nickel. Well, it worked for me ! If not, you might look into Ubuntu Linux-it's quite Windows-like. My family computer's motherboard is made by MSI, so I went to MSI's tech-support web site and found that they have a really nifty web-based hardware probe utility (beware: Explorer 5+ http://www.techspot.com/community/topics/cannot-install-windows-on-wd-500gb-sata-hard-drive.157671/

Western Digital Sata Hard Drive Jumper Settings

Is there a way to solve the issue or is it time to really start looking for a new computer? The reason for this is that you can only use them from floppy (normally) by pressing F6 during XP installation. If you wish to add another parition to the drive, select the Disk 0 Unallocated Space again and click on New to add another new partition to the hard drive. Adding an additional hard drive to a Windows Vista installation: Make sure your hard drive is detected by your Serial ATA or EIDE controller.

If the drive still is not detected after testing the cables, contact your controller card manufactuer to see if there is an update available. Thanks anyway Dave ! I don't think you read my question correctly. Toshiba 2.5 Sata Hard Drive Jumper Settings Continue steps 4 and 5 until the desired amount of partitions is obtained and then click on Next to continue installing Windows 7 on the first partition.

After some "next" clicks, I got a "Windows couldn't install the drive" or something like that message. Jumper Setting On Hard Disk March 21, 2012 Jon Hi, Dave, it is a spare I got from a friend and he used it for Linux only and gave it to me when he upgraded to Restore the image to the new SATA partition 4.. Thanks.

Insert the Windows XP CD into the CD-ROM drive and restart the system Follow the onscreen prompts until the partition list screen is displayed You should see your hard drive listed Toshiba Hard Drive Jumper Settings This might be a motherboard problem, but it might also be a power supply problem. During the installation process, you will be given the option to create partitions. But the nLite installer will tell you if you need it, and even ask if you want to get it and install it before it continues.

Jumper Setting On Hard Disk

But there is a way. check my blog Select a location on your hard drive. Western Digital Sata Hard Drive Jumper Settings I had an error such as :" reboot and select proper boot device or insert boot media in selected boot device and press a key" I checked bios and had to Wd10ezex Sata Jumper Settings Tim Phillips says: April 30, 2011 at 4:07 pm Thank you.

HDD now heres the problem:I formatted it. this contact form I had already re-partitioned. After finishing, a message pops up saying "remove disk 2 from the drive and click ok to restart". If you want multiple partitions on this hard drive see the additional instructions below: Adding Multiple Partitions to your Boot Drive durring a Windows 7 Installation: Important: Western Digital Technical Support Seagate Ide Hard Drive Jumper Settings

Left-click on Next to continue. Members can monitor the statuses of their requests from their account pages. Primary (C:) drive installation during Windows Vista setup: Make sure your drive is detected by your controller or in BIOS during bootup. have a peek here Insert the Windows 7 DVD into the DVD-ROM drive and restart the system.

it might work if i did that once or twice. Western Digital Hard Drive Installation Software John, thanks one more, and if you have some spare time, I would be glad for a response. BUT ALL OTHER DRIVES DO!!

The black has 64MB of cache while the blue has only 16MB.

If you have a custom built computer there may be an option to lengthen that seek time.Personally, I don't ever install an OS on a second or third hard drive while This message is displayed near the beginning of the installation process - just before the installer loads all of the pre-configured drivers on the CD. I went to Acer's website and found the drivers for XP but I don't which is the SATA driver. Function Of Jumper Pins In Hard Disk Follow the instructions in Answer ID 3865: How to partition and format a WD drive on Windows and macOS for Windows XP.

I never had this problem before. Thanks in advance. Facebook Google+ Twitter YouTube Subscribe to TechSpot RSS Get our weekly newsletter Search TechSpot Trending Hardware The Web Culture Mobile Gaming Apple Microsoft Google Reviews Graphics Laptops Smartphones CPUs Storage Cases Check This Out solved Windows 7 install cannot find my hard drive solved When I went to install windows 7 on a hard drive, it got rebooted in the process.

Now, I cannot boot onto any windows drive solved windows 7 cannot format hard drive during install solved Installed new hard drive, Windows 7 won\'t boot on Laptop solved Can't Install HDD. The runtime drivers exist only because subsequent service packs (SP1/2/3) added them to the operating system.